PACCAR SPN 91 FMI 16: Significado, Causas y Solución
Posición del Pedal del Acelerador — señal errática o inverosímil entre sensores duales
Reviewed by Diesel Mechanic Writers · Last updated August 04, 2026
Quick Answer
SPN 91 FMI 16 = Señal del Pedal del Acelerador Errática
Severity: 🟡 REVISAR EN PRÓXIMA PARADA · System: Accelerator Pedal Assembly (APP) · ⚠️ Conducir hasta la próxima parada
Referencia de Diagnóstico
| Campo | Detalles |
|---|---|
| Código | SPN 91 FMI 16 |
| Protocolo | J1939 SPN: 91 FMI: 16 |
| Componente | Accelerator Pedal Assembly (APP) |
| Fabricante | PACCAR |
| Serie de Motor | MX-13 |
| Severidad | |
| Referencia SAE | SAE J1939-73 Digital Annex — SPN 91, FMI 16 |
Causas Posibles
- Sensores de pedal Pista 1 y Pista 2 difieren en más del 10%
- Cableado rozado debajo de la cabina cerca del pedal
- Corrosión en conector del pedal
- Pedal no original instalado incorrectamente
- Tapete del piso interfiriendo con el recorrido del pedal
Causas Más Frecuentes (Ranking por Frecuencia)
- Corroded or loose sensor connector pins (35% of sensor/electrical faults)
- Wiring harness chafing causing intermittent open or short circuits (25%)
- Failed sensor providing out-of-range signal to ECM (20%)
- ECM 5V reference circuit overload from multiple sensor failures (10%)
- CAN bus communication fault from terminating resistor or module failure (10%)
Procedimiento de Diagnóstico Detallado
Siga estos pasos de diagnóstico para identificar la causa raíz de SPN 91 FMI 16 en su PACCAR MX-13. Se recomienda una herramienta de escaneo de diagnóstico compatible con J1939.
- Connect scan tool and retrieve all active and inactive fault codes, noting which modules are reporting communication errors
- Check battery voltage and ground connections — low system voltage (below 11V) or poor grounds cause erratic sensor readings and communication faults
- Backprobe the suspect sensor connector and measure reference voltage (typically 5V), signal voltage, and ground with a digital multimeter — compare readings to OEM specifications
- Inspect wiring harness for chafing, especially at common failure points: engine pass-through connectors, valve cover gasket connectors, and frame rail routing near sharp edges
- Perform wiggle test on the harness while monitoring live data — intermittent connections will cause sensor readings to spike or drop when the harness is moved
- If CAN bus faults are present, check terminating resistors (should measure 60 ohms across CAN high and CAN low with the key off and batteries disconnected)
Reparación y Estimación de Costos
| Concepto | Rango de Costo |
|---|---|
| Piezas | $150 – $1,200 |
| Mano de Obra | 2–6 horas @ ~$150/hr = $300 – $900 |
| Total Estimado | $450 – $2,100 |
Sensor replacement or harness repair. Los precios varían según ubicación y concesionario.
Preguntas Frecuentes — Accelerator Pedal Assembly (APP)
How do I know if a sensor is bad or if the wiring is the problem?
Backprobe the sensor connector and measure reference voltage, signal, and ground. If the 5V reference is present and ground is good, but the signal is out of range, the sensor is likely bad. If reference voltage is missing or unstable, the problem is in the wiring or ECM. A wiggle test on the harness while monitoring live data will reveal intermittent connections.
Can I drive with a faulty sensor?
It depends on the sensor. Non-critical sensors (barometric pressure, fuel temperature) typically trigger CHECK SOON codes and the engine runs on a default value. Critical sensors (accelerator pedal, crankshaft position) can cause stalling or no-start conditions. If the engine runs normally despite the code, you can usually drive to a repair facility, but do not ignore the code indefinitely.
What causes CAN bus communication faults?
CAN bus faults are caused by wiring damage (chafed or cut wires), corroded connectors, failed terminating resistors, or a faulty module that corrupts bus communication. Heavy-duty trucks use J1939 CAN which requires 120-ohm terminating resistors at each end of the bus. Measuring 60 ohms across CAN high and CAN low (with power off) confirms the bus is intact.
How much does an ECM replacement cost?
A new ECM for a heavy-duty diesel engine costs $1,500–$4,000 for the part alone, plus 3–6 hours of labor for installation, programming, and parameter setup. Remanufactured ECMs are available for $800–$2,000. Always verify the ECM is truly faulty before replacing — many ECM codes are caused by wiring or sensor issues, not the ECM itself.
Why do sensor faults seem to happen more in wet weather?
Moisture ingress into sensor connectors causes corrosion and intermittent electrical contact. This is especially common at the engine harness pass-through connector (where wires enter the valve cover) and at under-hood sensor connectors that are not properly sealed. Dielectric grease on connector pins and OEM-rated weatherpack connectors help prevent moisture-related faults.
Procedimiento de Diagnóstico y Reparación
- Paso 1: Verificar que el tapete no bloquee el recorrido completo del pedal
- Paso 2: Leer voltajes APP1 y APP2 con herramienta de escaneo (APP2 debe ser la mitad de APP1)
- Paso 3: Realizar procedimiento de calibración del pedal con software de diagnóstico
- Paso 4: Inspeccionar cableado debajo del tablero por rozaduras en columna de dirección
Preguntas Frecuentes
¿Qué distancia puedo conducir con SPN 91 FMI 16?
Este código REVISAR EN PRÓXIMA PARADA permite continuar operando hasta un lugar de servicio seguro, típicamente dentro de 80–160 km. Reduzca la carga del motor (evite pendientes pronunciadas, reduzca la velocidad de crucero) y monitoree de cerca los indicadores relacionados. Si aparecen síntomas secundarios — humo, ruido inusual, aumento de temperatura — deténgase inmediatamente.
¿Este código causará daño permanente al motor si sigo conduciendo?
Si se atiende pronto en la próxima parada, es poco probable que cause daño permanente. Sin embargo, la operación prolongada (más de 300 km) con esta falla activa puede agravar el problema. Por ejemplo, las fallas del sistema DEF eventualmente activarán una reducción completa de potencia y limitación de velocidad a 8 km/h. Algunas condiciones REVISAR EN PRÓXIMA PARADA pueden convertirse en DETENER MOTOR si la causa raíz empeora.
¿Puedo diagnosticar esto yo mismo o necesito un mecánico?
Puede intentar los pasos de diagnóstico indicados arriba. Muchos códigos REVISAR EN PRÓXIMA PARADA tienen causas sencillas — niveles bajos de fluidos, filtros obstruidos o conexiones sueltas — que un propietario-operador puede resolver. Sin embargo, si el código reaparece después de borrarlo, la falla subyacente requiere diagnóstico profesional con una herramienta de escaneo capaz de ver datos en vivo e información de congelación de cuadro.
Estimated Repair Cost
Typical repair: $200–1,500 (Parts: $150–1,000 + Labor: 1–4 hours) · Costs vary by make/model and location
Códigos de Falla Relacionados — MX-13
SPN 1077 FMI 14
🔴 DETENER MOTOR
SPN 1347 FMI 7
🔴 DETENER MOTOR
SPN 647 FMI 4
MID 130 PID 52 FMI 5
SPN 411 FMI 16
🟠 REVISAR PRONTO
MID 128 PID 105 FMI 10
🟠 REVISAR PRONTO
Códigos Relacionados en Otros Sistemas
Códigos del mismo rango SPN, fabricante o sistema que también pueden ser relevantes:
SPN 91 FMI 3
SPN 520210 FMI 31
🔴 DETENER MOTOR
SPN 524265 FMI 7
Síntomas Asociados
Referencias y Lecturas Adicionales
- SAE J1939-73: Capa de Aplicación — Diagnósticos. SAE International. Define la semántica de códigos de falla SPN 91 / FMI 16 para redes CAN de servicio pesado. SAE J1939 Standard
- PACCAR MX-13 Manual de Servicio: Procedimientos de diagnóstico OEM para fallas de Accelerator Pedal Assembly (APP). Consulte la documentación oficial de servicio de PACCAR para el número de serie específico de su motor.
- TMC RP 1210: Práctica Recomendada para Interfaz de Diagnóstico de Vehículos Basada en Windows. Technology & Maintenance Council (TMC) de American Trucking Associations.