Volvo SPN 4364 FMI 18: Significado, Causas y Solución
Inducción SCR — velocidad del vehículo limitada a 8 km/h a menos que se corrija la falla
Reviewed by Diesel Mechanic Writers · Last updated August 04, 2026
Quick Answer
SPN 4364 FMI 18 = Inducción SCR — Límite de Velocidad a 8 km/h
Severity: 🔴 DETENER MOTOR · System: SCR Aftertreatment System · ⛔ NO continuar conduciendo
⚠️ STOP DRIVING — This code indicates a critical safety issue. Continuing to operate the vehicle may cause engine damage or safety hazard. Pull over safely and diagnose before continuing.
Referencia de Diagnóstico
| Campo | Detalles |
|---|---|
| Código | SPN 4364 FMI 18 |
| Protocolo | J1939 SPN: 4364 FMI: 18 |
| Componente | SCR Aftertreatment System |
| Fabricante | Volvo |
| Serie de Motor | D13 |
| Severidad | 🔴 DETENER MOTOR |
| Referencia SAE | SAE J1939-73 Digital Annex — SPN 4364, FMI 18 |
Causas Posibles
- Tanque de DEF completamente vacío
- Múltiples fallas del sistema SCR activas simultáneamente
- Eficiencia de conversión de NOx por debajo del umbral de inducción
- Contaminación severa de calidad del DEF
Causas Más Frecuentes (Ranking por Frecuencia)
- Contaminated or diluted DEF fluid (30% of cases)
- DEF dosing valve / injector clogged with crystallized urea (25%)
- Failed or degraded NOx sensor giving incorrect readings (20%)
- DEF pump failure or low DEF pressure (15%)
- Wiring harness corrosion or open circuit in aftertreatment sensors (10%)
Procedimiento de Diagnóstico Detallado
Siga estos pasos de diagnóstico para identificar la causa raíz de SPN 4364 FMI 18 en su Volvo D13. Se recomienda una herramienta de escaneo de diagnóstico compatible con J1939.
- Connect scan tool and document all active and inactive aftertreatment fault codes — SCR faults often appear in groups; identify the primary and secondary codes
- Test DEF quality using a refractometer — DEF must be between 32.5% and 36.5% urea concentration; contaminated or diluted DEF is the #1 cause of SCR faults
- Inspect DEF tank for crystalized urea deposits, and check DEF filter (if equipped) for blockage — replace the filter if it has not been serviced per OEM schedule
- Perform NOx sensor diagnostic — compare inlet and outlet NOx sensor readings in live data; outlet should read significantly lower than inlet during normal SCR operation
- Check DEF dosing valve / injector for crystalized urea blockage — remove and inspect, clean or replace as needed
- Verify DPF differential pressure at idle and 1500 RPM; high backpressure can trigger false SCR-related codes and prevent proper regeneration
Reparación y Estimación de Costos
| Concepto | Rango de Costo |
|---|---|
| Piezas | $1,200 – $6,000 |
| Mano de Obra | 4–10 horas @ ~$150/hr = $600 – $1,500 |
| Total Estimado | $1,800 – $7,500 |
NOx sensor, DEF pump, or SCR catalyst replacement. Los precios varían según ubicación y concesionario.
Preguntas Frecuentes — SCR Aftertreatment System
Will a bad DEF sensor cause my truck to derate?
Yes. EPA-mandated inducement systems require the ECM to progressively derate the engine if DEF-related faults are not resolved. First, the ECM limits vehicle speed to 55 mph, then 45 mph, and eventually 5 mph. The derate typically activates 50–200 miles after the fault is first detected, depending on the specific code and OEM programming.
Can I just add fresh DEF to fix a quality problem?
If the DEF is contaminated with minerals, diesel, or water, simply adding fresh DEF will not fix the issue. The entire tank must be drained, flushed with deionized water, and refilled with fresh API-certified DEF. Running contaminated DEF through the dosing system can clog the injector and damage the SCR catalyst — a $3,000–$8,000 repair.
How do I test a NOx sensor to see if it is bad?
Using a scan tool, compare inlet and outlet NOx sensor readings at operating temperature. Under normal SCR operation, outlet NOx should be 70–90% lower than inlet. If both sensors read similar values, either the SCR is not dosing DEF or the outlet sensor has failed. You can also swap the inlet and outlet sensors — if the fault code moves to the other position, the sensor is bad.
How often should I replace the DEF filter?
Most OEMs recommend DEF filter replacement every 150,000–200,000 miles or at the first sign of crystallization. If you operate in extreme cold climates where DEF freezes and thaws frequently, inspect the filter every 100,000 miles. A clogged DEF filter causes low DEF pressure faults and can trigger a derate.
Can I bypass or delete the SCR system?
Removing or disabling the SCR system is a federal crime under the Clean Air Act and can result in fines up to $37,500 per violation. Many states perform roadside emissions testing, and deleted trucks fail DOT inspections. Additionally, SCR deletion voids the engine warranty and reduces resale value. Proper maintenance is far less expensive than the legal and financial consequences of tampering.
Procedimiento de Diagnóstico y Reparación
- Paso 1: Acción inmediata: rellenar DEF de contenedor sellado
- Paso 2: Verificar códigos de falla SCR activos y abordar causa raíz primero
- Paso 3: Realizar reinicio del sistema SCR con Volvo Tech Tool
- Paso 4: La eliminación completa de la reducción requiere pasar prueba de eficiencia SCR
Preguntas Frecuentes
¿Puedo seguir conduciendo con SPN 4364 FMI 18?
No. Esta es una falla de nivel DETENER MOTOR. Continuar operando causará daños severos al motor, incluyendo posible falla catastrófica. Deténgase de manera segura y diagnostique antes de reiniciar. Remolque el vehículo a un taller si no puede identificar y resolver la causa raíz en la carretera.
¿Cuál es el protocolo de emergencia?
1) Deténgase en el primer lugar seguro — use luces de emergencia y triángulos reflectantes si está en el arcén de una autopista. 2) Apague el motor. 3) Verifique problemas obvios: fugas de fluidos, humo, conexiones sueltas, olores inusuales. 4) Escanee códigos de falla secundarios usando la pantalla del tablero o herramienta de diagnóstico. 5) Llame a asistencia en carretera si no puede resolverlo. No intente llevar el vehículo al taller por sus propios medios.
¿Qué sucede si ignoro este código?
Ignorar un código DETENER MOTOR puede resultar en: falla del turbocompresor ($3,000–$8,000 USD), agarrotamiento del motor que requiere reconstrucción completa ($15,000–$40,000 USD), o riesgo de incendio por fuga de combustible/aceite sobre componentes calientes del escape. Si este código aparece junto con baja presión de aceite o alta temperatura del refrigerante, la falla del motor puede ocurrir en minutos.
Estimated Repair Cost
Typical repair: $500–3,000 (Parts: $300–2,000 + Labor: 2–8 hours) · Costs vary by make/model and location
Códigos de Falla Relacionados — D13
SPN 4375 FMI 7
SPN 174 FMI 0
SPN 3031 FMI 9
🟠 REVISAR PRONTO
MID 128 PSID 90 FMI 4
🟠 REVISAR PRONTO
SPN 107 FMI 16
🟠 REVISAR PRONTO
SPN 84 FMI 0
🟠 REVISAR PRONTO
Códigos Relacionados en Otros Sistemas
Códigos del mismo rango SPN, fabricante o sistema que también pueden ser relevantes:
SPN 4364 FMI 18
SPN 4334 FMI 7
SPN 4342 FMI 4
🟠 REVISAR PRONTO
SPN 102 FMI 1
SPN 174 FMI 3
SPN 3031 FMI 9
🟠 REVISAR PRONTO
SPN 1761 FMI 18
SPN 520605 FMI 7
SPN 3031 FMI 9
🟠 REVISAR PRONTO
Síntomas Asociados
Referencias y Lecturas Adicionales
- SAE J1939-73: Capa de Aplicación — Diagnósticos. SAE International. Define la semántica de códigos de falla SPN 4364 / FMI 18 para redes CAN de servicio pesado. SAE J1939 Standard
- Volvo D13 Manual de Servicio: Procedimientos de diagnóstico OEM para fallas de SCR Aftertreatment System. Consulte la documentación oficial de servicio de Volvo para el número de serie específico de su motor.
- TMC RP 1210: Práctica Recomendada para Interfaz de Diagnóstico de Vehículos Basada en Windows. Technology & Maintenance Council (TMC) de American Trucking Associations.